Tutorials

6 X 6" ONE SHEET WONDFOR THE BOX YOU WILL NEED:

The template that was used for this project was found at Verves Stamps

23.5cm Sqr Cardstock of choice                     Envelope Punch Board                        Sticky Strip

TO ASSEMBLE:
1.      Place cardstock on Envelope Punch Board and take left hand edge to 9.2cm
2.      Punch then score with the scoring tool attachment
3.       Move cardstock along to 11.2cm, punch and score THESE ARE THE ONLY TIMES YOU WILL NEED TO MEASURE
4.       Turn cardstock 90 deg, match the pointed arrow to where you have previously scored then punch and score
5.       Move cardstock to next score line and punch and score once again
6.       Continue steps 5 and 6 on the other two sides
7.       Using bone folder run along all scored edges
8.       Cut out little notch on each corner
9.       Using the corner rounder punch on the board, punch the tabs on the longest edge top and bottom
10.   Place a card on box front to make sure that it fits well
11.   Place sticky strip on lower edge of side triangles and making sure the sides are aligned then stick down

TO MAKE BELLY BAND:
Cut a strip of DSP 2.5 x 27cm DSP
Place around box, but not too tightly and secure with Sticky Strip
Add an embellishment of your liking to where the DSP meets

If you don’t want to put a bellyband around your card, punch out a modern label punch and attach to back of box using brads and the flap will just slip under it
  

INSTRUCTIONS FOR CARDS

Cut DSP as shown in Template.
The following pieces of cardstock are all Basic Black in this case.
Attach these pieces of card stock to the matching DSP panel and set aside in order

1a. 3 1/8 x 2 1/8                           1b.  3 1/8 x 3 3/8

2a.  5 3/8 x 7/8                             2b. 7/8 x 7/8

3a.  2 3/8 x 2 3/8                          3b.  7/8 x 2 3/8                                   3c. 2 3/8 x 1 1/8

4a.  2 3/8 x 2 1/8                          4b.  7/8 x 3 1/8

CARDS BASES:
All card bases are A5 Whisper White
Embossed Layer Perfect Polka Dots 10 14.3cm Cool Caribbean

FOCUS PANELS:

CARD 1:
2 3/8 x 2 3/8 Basic Black              2 ¼ x 2 ¼ Cool Caribbean                   2 1/8 x 2 1/8 Whisper White
Stamp image from Reason To Smile Clear Stamp Set in Cool Caribbean 
Attach focus panel to card front using dimensionals

CARD2:
Embossed Layer Mosaic Madness Cool Caribbean

FOCUS PANELS:

3 ¼ X 2 Basic Black                                   3 1/8 x 1 7/8 Cool Caribbean             3 x 1 ¾ Whisper White
Stamp image from Reason to Smile Clear Stamp Set in Cool Caribbean
Add focus panel to card front using dimensionals
Attach ribbon with glue dot

CARD 3:
Embossed Layer Perfect Polka Dots Cool Caribbean

FOCUS PANELS:

3 3/8 x 1 ½ Basic Black                 3 1/8 x 1 3/8 Cool Caribbean             3 x 1 ¼ Whisper White
Stamp image from Blooming With Kindness
Attach focus panel on card front using dimensionals

CARD 4:
Embossed layer Mosaic Madness

FOCUS PANELS:

Take scrap of Whisper White and stamp image from Reason to Smile, then cut out image.
Stamp image again , but the only piece you need is the centre which you will punch out using ½” circle punch
Punch out flower in Cool Caribbean
Place dimensional under the Cool Caribbean flower shape and attach to stamped image
Place dimensional under the ½” circle and attach to the punched flower
Place dimensionals under the stamped image and attach to card front
Attach to card front


*** If you need the measurements in cms see me and I will give them to you FOR CARDS AND BOX SET







Related Posts Plugin for WordPress, Blogger...